Font Size:big  middle  small

        LHR

        Number of visits: Date:2014-8-2 17:44

        LHR series         

        ● Endurance with ripple current:5000hours at 85℃
        ●Rated voltage range:350to450vdc,capacitance 680to18000µF
        ●Improved the resistance for charge and discharge from same dimension of LG series
        ●For frequently change of regenerative voltage from AC servo amplifier and inverter control.Electricity Giddy Machine. digital a transmitter circuit. supersonic (waves)

        ◆SPECIFIC ATIONS

        items

        Characteristics

        Category temperature Range

        -40~+85℃

        Rated voltage Range

        350~450VDC

        Capacitance Tolerance

        ± 20%(M) ------------------at 20℃/120HZ

        Leakage Current

        I=0.02CV or 5mA,whichever is smaller
        I: Where, I : Max. leakage current(µA)、C: Nominal capacitance(µF)、Rated voltage (V)at 20℃after 5 minutes)

        Dissipation Factor(tanδ)

        ≤0.20  -------------- at 20℃/120HZ

        Low Temperature  characteristics

        Capacitance change(vdc) C(-25℃)/C(+20℃)≥0.7 -------------- at 20℃/120HZ

        Insulation Resistance

        When measured between the terminals that are connected to each other and to the mounting clamp on the insulating sleeve covering the case by using an insulation resistance meter of 500Vdc, the insulation resistance shall not be less than 100mΩ

        Insulation Withstanding Voltage

        When a voltage of 2,000Vac is applied for 1 minute between the terminals that are connected to each other and to the mounting clamp on the insulating sleeve covering the case, there shall not be electrical damage.。

        Charge and Discharge

        The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to charge and discharge test with the voltage waveform shown below at room temperature(15to35℃)

        Capacitance change

        ≤±20% of the initial value

        Voltage waveform:

        D.F. (tanδ)

        ≤300% of the initial specified value

        Leakage current

        ≤The initial specified value

        Frequency

        3HZ

        Number of cycle

        60 million times

        Endurance

        The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated ripple current is applied (the peak voltage shall not

        Capacitance change

        ≤±20% of the initial value

        exceed the rated voltage) for 2,000 hours at 85℃。

        D.F. (tanδ)

        ≤200% of the initial specified value

        Leakage current

        ≤The initial specified value

        Shelf Life

        The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 500 hours at 85℃ without voltage applied. Before the measurement,

        Capacitance change

        ≤±20% of the initial value

        the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4

        D.F. (tanδ)

        ≤200% of the initial specified value

        Leakage current

        ≤The initial specified value

        SRANDRAD RATINGS

        W.V cap Case sizeD x L tanδ120HZ,20℃ Rated ripple current(Ams/85℃,120HZ) Part NO.
        [Vdc] [μF] [mm] [mΩ]
        350 1200 50*60 4.7 1.56 LHR351M5C122MC60
        1500 50*70 5.5 1.83 LHR351M5C152MC70
        1800 50*80 6.4 2.13 LHR351M5C182MC80
        2200 50*96 7.6 2.53 LHR351M5C222MC96
        2700 50*105 8.8 2.94 LHR351M5C272MCA5
        2700 50*115 9.2 3.06 LHR351M5C272MCB5
        3300 50*130 10.8 3.58 LHR351M5C332MCD0
        4700 63.5*115 13.2 4.61 LHR351M5C472MDB5
        5600 63.5*130 15.2 5.3 LHR351M5C562MDD0
        5600 76.2*105 15.2 5.36 LHR351M5C562MEA5
        6800 63.5*155 18.1 6.32 LHR351M5C682MDF5
        8200 63.5*170 20.7 7.25 LHR351M5C822MDH0
        8200 76.2*130 20.2 6.57 LHR351M5C822MED0
        10000 76.2*155 24.2 8.47 LDX351M5C103MEF5
        10000 89*115 23.1 8.1 LHR351M5C103MFB5
        12000 76.2*170 27.6 9.66 LHR351M5C123MEH0
        12000 89*130 26.6 9.33 LHR351M5C123MFD0
        15000 89*155 32.1 11.2 LHR351M5C153MFF5
        15000 89*170 33.5 11.7 LHR351M5C153MFH0
        18000 89*190 38.5 13.5 LHR351M5C183MFK0
        375 1000 50*60 4.3 1.42 LHR3H1M5C102MC60
        1200 50*70 4.9 1.64 LHR3H1M5C122MC70
        1500 50*80 5.8 1.94 LHR3H1M5C152MC80
        2200 50*96 7.6 2.54 LHR3H1M5C222MC96
        2200 50*105 8 2.65 LHR3H1M5C222MCA5
        2700 50*115 9.2 3.06 LHR3H1M5C272MCB5
        3300 50*130 10.8 3.58 LHR3H1M5C332MCD0
        4700 63.5*115 13.2 4.61 LHR3H1M5C472MDB5
        5600 63.5*130 15.2 5.3 LHR3H1M5C562MDD0
        5600 76.2*105 15.2 5.36 LHR3H1M5C562MEA5
        6800 63.5*155 18.1 6.32 LHR3H1M5C682MDF5
        6800 63.5*170 18.9 6.6 LHR3H1M5C682MDH0
        8200 76.2*130 20.2 7.09 LHR3H1M5C822MED0
        8200 89*115 20.9 7.35 LHR3H1M5C822MFB5
        375 10000 76.2*155 24.2 8.48 LHR3H1M5C103MEF5
        10000 76.2*170 25.2 8.85 LHR3H1M5C103MEH0
        10000 89*130 24.3 8.54 LHR3H1M5C103MFD0
        12000 89*155 28.4 10 LHR3H1M5C123MFF5
        15000 89*170 33.5 11.7 LHR3H1M5C153MFH0
        15000 89*190 35.2 12.3 LHR3H1M5C153MFK0
        400 1000 50*60 4.3 1.42 LHR401M5C102MC60
        1200 50*70 4.9 1.64 LHR401M5C122MC70
        1500 50*80 5.8 1.95 LHR401M5C152MC80
        1800 50*96 6.9 2.29 LHR401M5C182MC96
        2200 50*105 8 2.65 LHR401M5C222MCA5
        2200 50*115 8.3 2.77 LHR401M5C222MCB5
        2700 50*130 9.8 3.23 LHR401M5C272MCD0
        3900 63.5*115 12 4.21 LHR401M5C392MDB5
        4700 63.5*130 13.9 4.86 LHR401M5C472MDD0
        5600 63.5*155 16.4 5.75 LHR401M5C562MDF5
        5600 63.5*170 17.1 5.99 LHR401M5C562MDH0
        5600 76.2*105 15.2 5.35 LHR401M5C562MEA5
        6800 76.2*130 18.4 6.47 LHR401M5C682MED0
        8200 76.2*155 21.9 7.68 LHR401M5C822MEF5
        8200 76.2*170 22.8 8.02 LHR401M5C822MEH0
        8200 89*115 20.9 7.35 LHR401M5C822MFB5
        10000 89*130 24.3 8.26 LHR401M5C103MFD0
        12000 89*155 28.7 10 LHR401M5C123MFF5
        12000 89*170 29.9 10.5 LHR401M5C123MFH0
        15000 89*190 31.2 12.3 LHR401M5C153MFK0
        420 820 50*60 3.8 1.29 LHR421M5C821MC60
        1000 50*70 4.4 1.5 LHR421M5C102MC70
        1200 50*80 5.2 1.75 LHR421M5C122MC80
        1800 50*96 6.8 2.3 LHR421M5C182MC96
        1800 50*105 7.1 2.4 LHR421M5C182MCA5
        2200 50*115 8.2 2.77 LHR421M5C222MCB5
        2700 50*130 9.6 3.25 LHR421M5C272MCD0
        3300 63.5*115 11 3.87 LHR421M5C332MDB5
        3900 63.5*130 12.7 4.44 LHR421M5C392MDD0
        4700 63.5*155 15 5.28 LHR421M5C472MDF5
        4700 76.2*105 13.9 4.92 LHR421M5C472MEA5
        5600 63.5*170 17.1 6.02 LHR421M5C562MDH0
        5600 76.2*130 16.6 5.9 LHR421M5C562MED0
        6800 76.2*155 19.8 7.02 LHR421M5C682MEF5
        6800 89*115 19 6.73 LHR421M5C682MFB5
        8200 76.2*170 22.7 8.04 LHR421M5C822MEH0
        8200 89*130 22 7.78 LHR421M5C822MFD0
        10000 89*155 26.2 9.24 LHR421M5C103MFF5
        12000 89*170 29.9 10.5 LHR421M5C123MFH0
        12000 89*190 31.5 11 LHR421M5C123MFK0
        450 680 50*60 3.1 1.03 LHR451M5C681MC60
        820 50*60 3.8 1.29 LHR451M5C821MC60
        1000 50*70 4.4 1.5 LHR451M5C102MC70
        1200 50*80 5.2 1.74 LHR451M5C122MC80
        1500 50*96 6.2 2.1 LHR451M5C152MC96
        1800 50*115 7.4 2.51 LHR451M5C182MCB5
        2200 50*130 8.7 2.93 LHR451M5C222MCD0
        3300 63.5*115 11 3.88 LHR451M5C332MDB5
        3900 63.5*130 12.7 4.44 LHR451M5C392MDD0
        3900 76.2*105 13.2 4.49 LHR451M5C392MEA5
        4700 63.5*155 15 5.27 LHR451M5C472MDF5
        4700 63.5*170 15.6 5.5 LHR451M5C472MDH0
        5600 76.2*130 16.6 5.88 LHR451M5C562MED0
        6800 76.2*155 19.8 7.04 LHR451M5C682MEF5
        6800 89*115 19 6.72 LHR451M5C682MFB5
        8200 76.2*170 22.7 7.97 LHR451M5C822MEH0
        8200 89*130 22 7.72 LHR451M5C822MFD0
        10000 89*155 26.2 9.22 LHR451M5C103MFF5
        10000 89*170 27.3 9.66 LHR451M5C103MFH0
        12000 89*190 31.5 11.1 LHR451M5C123MFK0

        ◆ RTED RIPPLE CURRENT MUIERS

        The ripple frequency and standard list of the specified value is not at the same time, please use the value is less than the following

        ● Frequency Multipliers

        Frequency(HZ) 50 120 300 1K 3K
        coefficient 0.8 1.0 1.1 1.3 1.4

        Note : The endurance of capacitors is shorted with internal heating produced by ripple current at the rate of halving the lifetime with every 5 to 10℃ rise. When long life performance is required in actual use, the rms ripple current has to be reduced. Also, for the LB series capacitors, using them at operating voltage less than their rated voltage can extend their lifetime. For the details, please contact representative of capsun

        Previous post:LHC

        Next post:LHA

        Global  | NEWS | PRODUCTS | DOWNLOAD | CONTACT

        Copy Right SHENZHEN CAPSUN ELECTRONIC CO.,LTD 粤ICP备12063003号

        Add:Bao'an District, Shenzhen  TEL:+86-755-27299931 FAX:+86-755-33675266 E-mail:sunny@szcapsun.com